Rane SL 3 Manual del operador descargar pdf (Pagina 7)

RANE SL3 FOR SERATO SCRATCH LIVE • OPERATOR’S MANUAL 2.5.0

Playing Regular Vinyl and CDs

NOTE: the SL3 must be powered by

USB or the supplied external power

supply for the DECK THRUs to work.

If external power is connected, the SL3

is self-powered and power is not used

from the USB port.

If external power is not connected, the

SL3 draws power from the USB port.

Power switching is automatic and the

device continues to operate uninterrupted

as long as a power sources is available.

If you wish to use the SL3 Thru outputs

when a computer is not connected, you

will need to connect the optional external

power supply. Thrus are turned on and off

in the Control Panel.

To turn the Thrus off and on in Scratch

Live, click on the THRU button just above

each Virtual Deck for the respective

channel. This will change the state of the

channels to Thru Mode, sending audio

direct from the SL2 inputs to your mixer.

See “Thru Mode” on page 16.

Power Supply

Connect the barrel connector of the power

supply to the 7.5 VDC jack on the SL3.

Plug the power supply into an AC outlet.

The yellow POWER indicator will light on

the SL3.

The universal power supply includes

different input plugs for the USA, Europe,

UK and Australia. The USA plug is

attached at the factory — you may need

to replace it in your country.

To remove a

plug, PUSH the

button while turning

the outer rim

counterclockwise.

To attach a plug,

rotate it to t into

the supply and turn

clockwise until it locks in place.

The power supply is regulated 7.5

volts DC, 1 amp, using a P6 type barrel

plug. Any substitute must meet these

specications.

-(5.5mm) +(2.5mm)

LOCK

PUSH

OPEN

USB Drivers

The SL3 is a dual personality device.

When using Serato Scratch Live,

proprietary Serato Audio Research

drivers are used in place of Rane ASIO

(Windows) and Core Audio (Mac) drivers.

The included Rane drivers are used when

Scratch Live is not running.

Rane ASIO and Core Audio drivers

allow the SL3 to act as a 6-playback

and 6-record external USB sound card

for use with multiple third-party software

applications supporting Core Audio or

ASIO. ASIO and Core Audio drivers are

multi-client, meaning they allow multiple

applications on a computer to share

the device at the same time. ASIO and

Core Audio drivers are not available on a

machine when Scratch Live is running.

The ASIO and Core Audio drivers are

included in the Scratch Live installer as an

option. See the instructions in “Installing

Scratch Live” on page 8.

ASIO (Windows)

The SL3 uses a low-latency, multi-client,

ASIO device driver to interface with

software applications other than Scratch

Live on Windows operating systems.

Multi-client ASIO allows different audio

software applications to simultaneously

stream audio to and from the SL3. If the

same playback channel is selected in

more than one application, the driver

mixes the audio from different applications

before streaming it to the device.

The driver Control Panel may be

launched from the Windows Control

Panel. Select Start > Control Panel >

Rane SL3.

Core Audio (Macintosh)

The SL3 uses a low-latency, Core Audio

device driver to interface with software

applications other than Scratch Live

on Macintosh operating systems. Core

Audio allows different audio software

applications to simultaneously stream

audio to and from the SL3.

To launch the SL3 driver Control Panel,

open the System Preferences window.

Locate the SL3 in the “Other” section and

click the SL3 icon.

Control Panel

The Driver Control Panel supports:

• Analog Input Source: for Aux, Left

Deck and Right Deck, the Input as

selected on the SL3 is indicated. The

mode cannot be changed from the

control panel.

• Phono Sensitivity: control appears

as shown in the panel above if Phono

input is selected on the mixer. Clicking

on the down-arrow displays a list of

16 sensitivity settings between 2.5 mV

and 10 mV in 0.5 mV steps. Choose

the setting that most closely matches

the level of a CD input or to the setting

that provides the highest output without

clipping.

• Output Source: can be set for

independently for each of the three

stereo outputs. Click the USB icon for

USB playback and the Analog button for

analog THRU.

• Buffer Size increases or decreases the

USB driver buffer size. The SL3 drivers

run very reliably at latencies below

8 milliseconds. However, computer

performance and available resources

(number of apps running) may adversely

affect streaming audio. If pops and

clicks are heard in USB audio, try

increasing the buffer size. In ASIO, total

round-trip latency = buffer size + device

latency. In Core Audio, total round-

trip latency = buffer size + software

application latency + device latency. SL3

latency is 1.6 ms at 48 kHz and 1.8 ms

at 44.1 kHz.

• If the SL3 rmware on your computer

is newer than installed in your SL3,

the Update Device Firmware panel is

enabled. Pressing the Update Firmware

button updates the SL3 rmware to the

newer version installed with your driver.

1 2 3 4 5 6 7 8 9 10 11 12 ... 43 44

Comentarios a estos manuales

Sin comentarios

Rane SL 3 Manual del operador Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Controladores de dj Rane SL 3